ramcharger fan anyone have a pix of one mounted?

anyone have a pix of a Ramchargers double fn mounted.....it looks very wide for my mustang (stock 3 3core)?....

thanks


Mike

Mike, Hawk runs one. Look thru his photopost or on his website, If not go I'm sure he'll snap a pic if needed.

http://www.novipower.com/forums/images/top_search.gif

I did SEARCH.....the pix's on Hawks post are not showing up?...ill try a different browser?


Mike

Here you go..lots of info here...

http://www.novipower.com/forums/sear...der=descending

Chuck

Damn.....cardomain lost my fan pics and I can't upload new ones because my computer is dead (working with my back up cheapo job right now) I did find this one though that shows how tight the fit is with the 10 rib pulleys. The rad is a 3 core copper brass. Keep in mind too that my engine bay is actually smaller lengthwise than a Mustang.
http://images.cardomain.com/member_i...6_159_full.jpg

Hawk, can you measure the width of the radiator AND fan together? I've got the ramcharger fan, but Im trying to figure out if I can fit a 3 core radiator as well. Thanks.

The good hawk pic.:)

http://www.superchargerhelp.com/phot...ershawkfan.jpg

http://www.gapack201.com/New radiato...fan rev006.jpg

Fans mounted on Fluidyne

Quote:

---

Originally posted by pupdog5oh
http://www.gapack201.com/New radiato...fan rev006.jpg

Fans mounted on Fluidyne

---

Do you have pics of that from the top? And do you have a measurement of the width of the fan/radiator combo? Im assuming that's a 2 row fluidyne?

Ross,

It is a 2 row Fluidyne. It is the same thickness as the 3 row Modine I replaced it with. I will take some shots of the top and try to post them tomorrow....BTW, I have the 2 belt Novi setup with 8 rib pulley and I have probably an inch and a half or so clearance. Plenty of room.

Quote:

---

Originally posted by Blu50Stang
Hawk, can you measure the width of the radiator AND fan together? I've got the ramcharger fan, but Im trying to figure out if I can fit a 3 core radiator as well. Thanks.

---

I no longer have it mounted on a 3 core coper/brass rad as in my original picture that's posted above. I'll measure my old rad (still have it) and the fan and give you both measurements. I've added a pic below of a top view with the Ramcharger fan on my old 3 core copper/brass setup. This fan/rad combo will fit no problem in a Mustang with a blower...even a Novi2000 with it's 10 rib set up. See my earlier post that has a pic showing the clearnce between the fan and pulleys...that is with the 3 core rad. I did zero trimming to clear the crank blower pulley with the old set up (not so with the 2 core aluminum/Ramcharger combo) Keep in mind as well that my T-Bird's engine compartment is actually 1 inch shorter than a Mustang's. I've also attached a pic of a Ramcharger fan mounted on a Griffin 2 core aluminum rad installed in a Mustang with an 8 rib Vortech setup. The rad was mounted in the stock location and as you can see, it has plenty of room.

Ramcharger/3 core copper/brass rad combo

http://images.cardomain.com/member_i...6_144_full.jpg

Ramcharger/ 2 core Griffin Aluminum 19 x 31 Rad Combo

http://images.cardomain.com/member_i...6_145_full.jpg

Pup and Hawk, thanks.

I measured my 3 core copper/brass rad. It is 2" thick so with the Ramcharger fan being 3 5/8" that would make for a total of 5 5/8".

Thanks again Hawk.