PLEASE! Post your engine setup for the Novi100:

[NotchKing]

Hello,
I was wondering perhaps if everyone can post their setup so I can see what everyone is doing. Perhaps other people can benefit from this as well. Here is mine (you can follow the same format):

-bottomend: stock bottom end except it was rebuilt last year w/ hyperteunic pistons :bonk: polished crankshaft, new bearings, but everything else is stock. The cylinder walls were just honed but not bored because they didn't need to be

-Cyl. heads: stock
-upper/lower intake: stock
-Cam: CompCam duration/lift
-fuel injectors: stock
-fuel pump: stock
-fuel regulator: stock
-fuel rails: stock
-TB: stock
-MAF: stock
-air intake: BBK CAI, in the fender

I'm upgrading to a Novi 1000 w/ 30# FMS injectors, 255 BBK fuel pump, and BBK fuel regulator as soon as a I can. I'm also planning on upgrading to probably a Griffin radiator w/ a dual electric fan. Head and intake work will be later. :)

Oh, and I've owned my car every since November of 2002 :)

in Christ,
Jonathan

[sinner]

92 coupe
Stock bottom end
Stock cam
Paxton Novi 1000 (revised unit)
8" ASP Crank pulley/ bosch bypass valve
8lbs of boost
Edelbrock RPM heads (1.90/1.64)
Typhoon Intake
1.6 crane energizer rockers/hardend push rods
9mm Motorsports plug wires/ MSD coil
65mm TB
75mm Pro-M
42lb. injectors
190lph fuel pump
Made 392 HP and 373 TQ at the rear wheels on a Mustang dyno with a messed up fuel ratio, I go back for more tuning to fix this and they say the power will go up and I'm getting a powerpipe to make sure it goes up even more

[Mike Gager]

90 hatch
TRW forged bottom end
F-303 cam
Paxton Novi 1000 (old style unit)
F150 Crank pulley/ bosch bypass valve
power pipe
GT40 cast iron heads
93 cobra Intake
1.6 motorsport rockers
65mm TB
90mm Lightning MAFS
EEC tuner/A9L
42lb. injectors
255lph fuel pump
BBK shorty headers/off road H/flowmasters
T5Z/king cobra clutch/alluminum driveshaft/3.73 gears

should have mine up and running by the end of the month, hopefully sooner. looking for 380-400 rearwheel hp

[NotchKing]

Sweet setups so far! Anyone else?

[lx-convertible]

see below

[468LC]

See Below.:)

[NotchKing]

Thanks everyone so far :)
Any more?

[88gt]

track heat heads, gasket matched (felpro 1250) cobra intake, afm n-41 cam, tfs 1.6 rr's, frpp shorty's, bassani off road x-pipe, 2 chamber flows with dumps, 24#injectors, 75mm pro-m maf, 75mm bbk tb, walbor 190 in-tank, walbro 255 in-line, accufab afpr, 6:1 fmu, novi 1000, 3.73, 31 spline auburn hd, nitto d/r's = :D cars all over the place through 3rd gear and part of 4th

[mheinjr]

Below...

[frank woodall]

see below except now threw the FMU in the trash.......:D

[green93notch]

everything's down below :D

[green93notch]

everything's down below :D

[mheinjr]

Hey green93notch:

Are you just posing? Cause aren't you supposed to have a helmet on?

[allen]

novi 2000 stock pulleys 306 eagle crank and rods cp pistons out of the box trick flow heads out of the box trick flow intake 1 5/8 shorty headers x pipe flowmaster mufflers 50lb msd injedctors bullet mass meter tko trans 3.55 gear weldon 2035 fuel pump
car made 570 hp at the tire at 6100 stock computor no chip or engine management system 1.39 60ft 6.50 1/8 at 106 10.30 at 133mph at 3300lbs it went 10.40s at 130 with a 90,000 mile stock short block in it and oh yeah i almost forgot to add the fact that it has a stock 5.0L cam and not a cobra cam

[Qkhorse]

88lx hatch
block .020 over speed pro piston w/.060 thou deep valve reliefs
flow master 2.5" exhaust w/stock h-pipe
mach shorty headers
world product roush 200 cfm heads 2.02,1.60 valves
1.6 roller rockers
f303 cam 5.12 lift 2.26 duration
tricklfow street heat intake w/1 inch spacer
65mm TB
73mm c&L MAF
24lb jectors
adjustable fuel regulator
255lph intake pump
FMU (came with it)
paxton sn93 blower
home made power pipe
3.55 gears
c-4 tranny w/3500 stall torque w/manual valve body

Ran 1/8 7.800 @88.90 mph 1.75 60" none tuned yet with 5lbs boost. with mickey t's E.T street tires (15lbs tire pressure)