Results 1 to 12 of 12

Thread: 16-18psi

  1. 12-16-2003, 10:31 PM #1
    FMGT1999
    FMGT1999 is offline
    Junior SCH Member FMGT1999's Avatar
    Join Date
    Apr 2003
    Location
    Overland Park, Kansas
    Posts
    31

    Question 16-18psi

    I'm going to be lazy here and just ask, what size pully do I need to get to reach 16-18psi? And does anyone here know what size belt I'm going to need (ie a part number) for this application on a V2 mod engine?

    Thanks,
    Kyle
    Team DEDPEDAL Racing
    www.KC-MUSTANGS.com
    NMRA M/M 7113
    Reply With Quote Reply With Quote
  2. 12-19-2003, 01:09 AM #2
    FMGT1999
    FMGT1999 is offline
    Junior SCH Member FMGT1999's Avatar
    Join Date
    Apr 2003
    Location
    Overland Park, Kansas
    Posts
    31
    Umm... Hello? Any one out there...?
    Attached Images Attached Images
    Reply With Quote Reply With Quote
  3. 12-20-2003, 08:18 AM #3
    bumblebee03
    bumblebee03 is offline
    Senior SCH Member bumblebee03's Avatar
    Join Date
    Feb 2003
    Posts
    236
    Give Vortech a call,, but I think you need something under 2.50. . . and I would go with a 10 rib setup or a cog depending on how much you drive the car on the street. My 7" crank with a 2.95 pully produces 10lbs at 5600 ft above sea level, which would be about 12-14 at sea level,, Bee
    Reply With Quote Reply With Quote
  4. 03-10-2004, 09:37 PM #4
    93 GT
    93 GT is offline
    Junior SCH Member
    Join Date
    Dec 2003
    Posts
    21
    8 Rib? 2.85 & 8' will get you there!
    Reply With Quote Reply With Quote
  5. 03-10-2004, 09:38 PM #5
    93 GT
    93 GT is offline
    Junior SCH Member
    Join Date
    Dec 2003
    Posts
    21
    sorry,I see its a 1999 Stang.
    Reply With Quote Reply With Quote
  6. 03-11-2004, 05:35 AM #6
    midnight
    midnight is offline
    Senior SCH Member
    Join Date
    Feb 2003
    Posts
    132
    Don't think u r going 2 get there!!!!!!
    Reply With Quote Reply With Quote
  7. 03-12-2004, 11:07 PM #7
    FMGT1999
    FMGT1999 is offline
    Junior SCH Member FMGT1999's Avatar
    Join Date
    Apr 2003
    Location
    Overland Park, Kansas
    Posts
    31
    Midnight, I would be welling to say you’re in error. I have been in contact with Vortech and now have the information that I was looking for along with the part numbers that I need to reach my goal. Thank you for your incorrect opinion.
    Last edited by FMGT1999; 03-12-2004 at 11:13 PM.
    Reply With Quote Reply With Quote
  8. 03-12-2004, 11:10 PM #8
    FMGT1999
    FMGT1999 is offline
    Junior SCH Member FMGT1999's Avatar
    Join Date
    Apr 2003
    Location
    Overland Park, Kansas
    Posts
    31
    .
    Reply With Quote Reply With Quote
  9. 03-13-2004, 04:26 PM #9
    midnight
    midnight is offline
    Senior SCH Member
    Join Date
    Feb 2003
    Posts
    132
    Was not flaming & you're welcome..I'd like 2 know what the pulley sizes recommended by Vortech and by Who there..Further after u install them get back & let me know how stupid i am..Been doing this a long time..IMHO i still don't think u w/get there unless u figure out some cogs....
    Reply With Quote Reply With Quote
  10. 03-28-2004, 10:23 AM #10
    I8URICE
    I8URICE is offline
    Junior SCH Member I8URICE's Avatar
    Join Date
    Jan 2004
    Location
    NEW HAMPSHIRE/NEW ENGLAND PATRIOTS COUNTRY!!
    Posts
    20
    Edited by Ian - no swearing, or putting down others on this site.
    Last edited by Ian; 06-07-2004 at 11:28 PM.
    Reply With Quote Reply With Quote
  11. 06-07-2004, 10:46 PM #11
    FMGT1999
    FMGT1999 is offline
    Junior SCH Member FMGT1999's Avatar
    Join Date
    Apr 2003
    Location
    Overland Park, Kansas
    Posts
    31

    Wink

    Hey IBURICE... KMA,

    Hi midnight,

    Sorry I don't recall ever stating you being stupid in any of my posts to you, if you misinterpreted it that way I would like to apologize for any misunderstandings. Also like you stated, I am not trying to flame you either. I have a 6.8 crank pulley and a 3.125 pulley. That is the maximum power setup for my V-2 SQ system. That should put me in the 50,000+ rpm range which is about the maximum that I can go in that Vortech setup. Now correct me if I'm wrong here but at maximum rpm on the V-2 SQ system, isn't 18-20psi what I should be seeing?

    Let me know what you think,
    Thanks,
    Kyle
    Last edited by FMGT1999; 06-07-2004 at 11:04 PM.
    Team DEDPEDAL Racing
    www.KC-MUSTANGS.com
    NMRA M/M 7113
    Reply With Quote Reply With Quote
  12. 06-08-2004, 10:50 AM #12
    RSNovi
    RSNovi is offline
    Senior SCH Member
    Join Date
    Nov 2002
    Posts
    482
    I see S-Trims reaching 20#'s of boost all of the time.
    Chris
    9.05@152 with a T-Trim on BFG Drag Radials
    NMCA SR6381
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules