have linclon mark vii ,,ys trim, fast system, areomotive fuel system ,estimate 720 rwhp , question is what size injectors? i am thinking 83#'s with elimator pump mabye 2?:(
have linclon mark vii ,,ys trim, fast system, areomotive fuel system ,estimate 720 rwhp , question is what size injectors? i am thinking 83#'s with elimator pump mabye 2?
90 linclon mark vii
engine
342, dart block,crower billet crank, olivier rods, je custom pistons 8to1 compression,cometic head gaskets,
heads
AFR 205 heads,60cc,75cc exhaust ports
valve train
crane roller 1.6 roller lifters,manely custom pushrods,
crower tie bar solid lifters
blower
ys trim vortech blower
custom 1/2 "blower bracket,10rib 3.3" blower , 7"crank pulley,
cog drive setup 85 tooth/74 tooth crank, 27/30 thooth blower,
anderson power pipe,vortech mondo blowoff valve, custom blower brace,
exhaust
bassani 1 3/4 shorties, 3"mac pro chamber, 3"pro dumps,
induction
holley system max intake,1"intake spacer, accufab 75 mm t -body,
Engine managment system
fast system bank to bank w/wideband o2,crane ingition hi 6 r box and coil,
msd pro billet distubitor.
cooling system
fulidine radiator,edelbrock water pump,ramchargers dual fan setup,
chassi
custom 6pt roll cage, wild rides battle boxes,mm panhard bar,
sub frame conn., tublar k frame, coil conversion from air ride,
hpm custom control lower arms,adjustable uppers, kyb adjustable
shocks front, bilstines in rear,adj.camber plates,
rear
8.8,welded axels tubes,axels braces,
moser 33"s, strange locker , 3.73 gearset
transmission
lentech strip terminator 3000 stall speed convertor non lockup
fuel system
areomotive fuel system,
custom sumped tank.
You might as well go for the big 150's, and leave yourself room to grow. The FAST can handle them. Get a Weldon pump and be done w/ the fuel system. Play it on the safe side, buy everything just once.
FFW DR27
You are in the same boat I am in. I also have the areomotive fuel system, with the Eliminator fuel pump. This pump is suppose to be able to handle up to 900 hp forced induction. But, what I am hearing is it will not be enough fuel. The Weldon 2025 is suppose to be a better choice, or go with two Eliminator pumps.
My combo is a 393 with a YS-trim. I bought 83 lb Deka Seiman injectors which should be enough.
393 stroker with YS-trim Vortech :-)
JHenke
thanks for your input thats how i like to do thing once.
90 linclon mark vii
engine
342, dart block,crower billet crank, olivier rods, je custom pistons 8to1 compression,cometic head gaskets,
heads
AFR 205 heads,60cc,75cc exhaust ports
valve train
crane roller 1.6 roller lifters,manely custom pushrods,
crower tie bar solid lifters
blower
ys trim vortech blower
custom 1/2 "blower bracket,10rib 3.3" blower , 7"crank pulley,
cog drive setup 85 tooth/74 tooth crank, 27/30 thooth blower,
anderson power pipe,vortech mondo blowoff valve, custom blower brace,
exhaust
bassani 1 3/4 shorties, 3"mac pro chamber, 3"pro dumps,
induction
holley system max intake,1"intake spacer, accufab 75 mm t -body,
Engine managment system
fast system bank to bank w/wideband o2,crane ingition hi 6 r box and coil,
msd pro billet distubitor.
cooling system
fulidine radiator,edelbrock water pump,ramchargers dual fan setup,
chassi
custom 6pt roll cage, wild rides battle boxes,mm panhard bar,
sub frame conn., tublar k frame, coil conversion from air ride,
hpm custom control lower arms,adjustable uppers, kyb adjustable
shocks front, bilstines in rear,adj.camber plates,
rear
8.8,welded axels tubes,axels braces,
moser 33"s, strange locker , 3.73 gearset
transmission
lentech strip terminator 3000 stall speed convertor non lockup
fuel system
areomotive fuel system,
custom sumped tank.
Brcuda
thanks i will keep in mind ,what are you using for engine managment? because i saw pro m injector driver for $175 on ebay.
90 linclon mark vii
engine
342, dart block,crower billet crank, olivier rods, je custom pistons 8to1 compression,cometic head gaskets,
heads
AFR 205 heads,60cc,75cc exhaust ports
valve train
crane roller 1.6 roller lifters,manely custom pushrods,
crower tie bar solid lifters
blower
ys trim vortech blower
custom 1/2 "blower bracket,10rib 3.3" blower , 7"crank pulley,
cog drive setup 85 tooth/74 tooth crank, 27/30 thooth blower,
anderson power pipe,vortech mondo blowoff valve, custom blower brace,
exhaust
bassani 1 3/4 shorties, 3"mac pro chamber, 3"pro dumps,
induction
holley system max intake,1"intake spacer, accufab 75 mm t -body,
Engine managment system
fast system bank to bank w/wideband o2,crane ingition hi 6 r box and coil,
msd pro billet distubitor.
cooling system
fulidine radiator,edelbrock water pump,ramchargers dual fan setup,
chassi
custom 6pt roll cage, wild rides battle boxes,mm panhard bar,
sub frame conn., tublar k frame, coil conversion from air ride,
hpm custom control lower arms,adjustable uppers, kyb adjustable
shocks front, bilstines in rear,adj.camber plates,
rear
8.8,welded axels tubes,axels braces,
moser 33"s, strange locker , 3.73 gearset
transmission
lentech strip terminator 3000 stall speed convertor non lockup
fuel system
areomotive fuel system,
custom sumped tank.
I bought a PMS with the low impedance driver last year in a group purchase.
393 stroker with YS-trim Vortech :-)
I made over 800RW and have run 8.90s with a Weldon 2025 and SD 83lb injectors.
Spence
8.96/160
I have been watching that one tooOriginally posted by blownmarkvii
because i saw pro m injector driver for $175 on ebay.
Eric
1990 Mustang GT
9.20 @151.18
Check out this forum for AOD's/C4's: Click Click Racing Forums
My Homepage
RdRunnr
did you see pms for 500 buy now?
item# 2403035639
90 linclon mark vii
engine
342, dart block,crower billet crank, olivier rods, je custom pistons 8to1 compression,cometic head gaskets,
heads
AFR 205 heads,60cc,75cc exhaust ports
valve train
crane roller 1.6 roller lifters,manely custom pushrods,
crower tie bar solid lifters
blower
ys trim vortech blower
custom 1/2 "blower bracket,10rib 3.3" blower , 7"crank pulley,
cog drive setup 85 tooth/74 tooth crank, 27/30 thooth blower,
anderson power pipe,vortech mondo blowoff valve, custom blower brace,
exhaust
bassani 1 3/4 shorties, 3"mac pro chamber, 3"pro dumps,
induction
holley system max intake,1"intake spacer, accufab 75 mm t -body,
Engine managment system
fast system bank to bank w/wideband o2,crane ingition hi 6 r box and coil,
msd pro billet distubitor.
cooling system
fulidine radiator,edelbrock water pump,ramchargers dual fan setup,
chassi
custom 6pt roll cage, wild rides battle boxes,mm panhard bar,
sub frame conn., tublar k frame, coil conversion from air ride,
hpm custom control lower arms,adjustable uppers, kyb adjustable
shocks front, bilstines in rear,adj.camber plates,
rear
8.8,welded axels tubes,axels braces,
moser 33"s, strange locker , 3.73 gearset
transmission
lentech strip terminator 3000 stall speed convertor non lockup
fuel system
areomotive fuel system,
custom sumped tank.
I've made 781 rwhp with an aeromotive eliminator fuel pump and 83# injectors.
I am glad to hear I am not too far off. Thanks for your input.Originally posted by Andrew
I've made 781 rwhp with an aeromotive eliminator fuel pump and 83# injectors.
393 stroker with YS-trim Vortech :-)
can any one point me in right direction? how do yo make a start
up program or can you order one from f.a.s.t.?
90 linclon mark vii
engine
342, dart block,crower billet crank, olivier rods, je custom pistons 8to1 compression,cometic head gaskets,
heads
AFR 205 heads,60cc,75cc exhaust ports
valve train
crane roller 1.6 roller lifters,manely custom pushrods,
crower tie bar solid lifters
blower
ys trim vortech blower
custom 1/2 "blower bracket,10rib 3.3" blower , 7"crank pulley,
cog drive setup 85 tooth/74 tooth crank, 27/30 thooth blower,
anderson power pipe,vortech mondo blowoff valve, custom blower brace,
exhaust
bassani 1 3/4 shorties, 3"mac pro chamber, 3"pro dumps,
induction
holley system max intake,1"intake spacer, accufab 75 mm t -body,
Engine managment system
fast system bank to bank w/wideband o2,crane ingition hi 6 r box and coil,
msd pro billet distubitor.
cooling system
fulidine radiator,edelbrock water pump,ramchargers dual fan setup,
chassi
custom 6pt roll cage, wild rides battle boxes,mm panhard bar,
sub frame conn., tublar k frame, coil conversion from air ride,
hpm custom control lower arms,adjustable uppers, kyb adjustable
shocks front, bilstines in rear,adj.camber plates,
rear
8.8,welded axels tubes,axels braces,
moser 33"s, strange locker , 3.73 gearset
transmission
lentech strip terminator 3000 stall speed convertor non lockup
fuel system
areomotive fuel system,
custom sumped tank.
Call Job Spetter @ Turbo People. 914-478-1727
FFW DR27
Agree with Jim, get somebody reputable with the system to get you started and close. The system is not that complicated, but when you first start with it, you will need help. ALong with Job, In your area would be Dale Cherry from Berrel Automotive and Second Street SPeed, all three very reputable tuners and close enough that you wouldnt have to travel to aweful far.
Spence
8.96/160
thanks Spence,
i will have to look up those guy i greatful for the help.
thanks
90 linclon mark vii
engine
342, dart block,crower billet crank, olivier rods, je custom pistons 8to1 compression,cometic head gaskets,
heads
AFR 205 heads,60cc,75cc exhaust ports
valve train
crane roller 1.6 roller lifters,manely custom pushrods,
crower tie bar solid lifters
blower
ys trim vortech blower
custom 1/2 "blower bracket,10rib 3.3" blower , 7"crank pulley,
cog drive setup 85 tooth/74 tooth crank, 27/30 thooth blower,
anderson power pipe,vortech mondo blowoff valve, custom blower brace,
exhaust
bassani 1 3/4 shorties, 3"mac pro chamber, 3"pro dumps,
induction
holley system max intake,1"intake spacer, accufab 75 mm t -body,
Engine managment system
fast system bank to bank w/wideband o2,crane ingition hi 6 r box and coil,
msd pro billet distubitor.
cooling system
fulidine radiator,edelbrock water pump,ramchargers dual fan setup,
chassi
custom 6pt roll cage, wild rides battle boxes,mm panhard bar,
sub frame conn., tublar k frame, coil conversion from air ride,
hpm custom control lower arms,adjustable uppers, kyb adjustable
shocks front, bilstines in rear,adj.camber plates,
rear
8.8,welded axels tubes,axels braces,
moser 33"s, strange locker , 3.73 gearset
transmission
lentech strip terminator 3000 stall speed convertor non lockup
fuel system
areomotive fuel system,
custom sumped tank.
Posting Permissions
Reply With Quote
Bookmarks