i running areomotive rails a 600 + hp dont want to return off
driver side out of middle want to run out of the front but my
msd pro billet ditubitor is in the way ,dont want to grind the
**** out of the cap any thought would be helpful
i running areomotive rails a 600 + hp dont want to return off
driver side out of middle want to run out of the front but my
msd pro billet ditubitor is in the way ,dont want to grind the
**** out of the cap any thought would be helpful
90 linclon mark vii
engine
342, dart block,crower billet crank, olivier rods, je custom pistons 8to1 compression,cometic head gaskets,
heads
AFR 205 heads,60cc,75cc exhaust ports
valve train
crane roller 1.6 roller lifters,manely custom pushrods,
crower tie bar solid lifters
blower
ys trim vortech blower
custom 1/2 "blower bracket,10rib 3.3" blower , 7"crank pulley,
cog drive setup 85 tooth/74 tooth crank, 27/30 thooth blower,
anderson power pipe,vortech mondo blowoff valve, custom blower brace,
exhaust
bassani 1 3/4 shorties, 3"mac pro chamber, 3"pro dumps,
induction
holley system max intake,1"intake spacer, accufab 75 mm t -body,
Engine managment system
fast system bank to bank w/wideband o2,crane ingition hi 6 r box and coil,
msd pro billet distubitor.
cooling system
fulidine radiator,edelbrock water pump,ramchargers dual fan setup,
chassi
custom 6pt roll cage, wild rides battle boxes,mm panhard bar,
sub frame conn., tublar k frame, coil conversion from air ride,
hpm custom control lower arms,adjustable uppers, kyb adjustable
shocks front, bilstines in rear,adj.camber plates,
rear
8.8,welded axels tubes,axels braces,
moser 33"s, strange locker , 3.73 gearset
transmission
lentech strip terminator 3000 stall speed convertor non lockup
fuel system
areomotive fuel system,
custom sumped tank.
I was worried about that as well, but I spoke with Jack @ MM, and he made alot more than 600 and he returned in the middle.
Otherwise you will have to put washers under the rail mounts to move them out.
Ian
now i can sleep better.didnt like washer thing,it worried me that he injectors wouldn't seat right.
90 linclon mark vii
engine
342, dart block,crower billet crank, olivier rods, je custom pistons 8to1 compression,cometic head gaskets,
heads
AFR 205 heads,60cc,75cc exhaust ports
valve train
crane roller 1.6 roller lifters,manely custom pushrods,
crower tie bar solid lifters
blower
ys trim vortech blower
custom 1/2 "blower bracket,10rib 3.3" blower , 7"crank pulley,
cog drive setup 85 tooth/74 tooth crank, 27/30 thooth blower,
anderson power pipe,vortech mondo blowoff valve, custom blower brace,
exhaust
bassani 1 3/4 shorties, 3"mac pro chamber, 3"pro dumps,
induction
holley system max intake,1"intake spacer, accufab 75 mm t -body,
Engine managment system
fast system bank to bank w/wideband o2,crane ingition hi 6 r box and coil,
msd pro billet distubitor.
cooling system
fulidine radiator,edelbrock water pump,ramchargers dual fan setup,
chassi
custom 6pt roll cage, wild rides battle boxes,mm panhard bar,
sub frame conn., tublar k frame, coil conversion from air ride,
hpm custom control lower arms,adjustable uppers, kyb adjustable
shocks front, bilstines in rear,adj.camber plates,
rear
8.8,welded axels tubes,axels braces,
moser 33"s, strange locker , 3.73 gearset
transmission
lentech strip terminator 3000 stall speed convertor non lockup
fuel system
areomotive fuel system,
custom sumped tank.
The washer thing doesn't give you enough clearance. I think it's piss poor design on Aeromotive's part especially since they are made for 302's. I notched my old dist., so I could return from the front. I just installed an MSD Pro-Billet, and I will now be pulling my return from the middle. There is no way I am cutting or grinding this pretty dist.
302 shortblock, X303 heads, E303 cam, SVO 1.6 roller rockers, Hogans upper, GT40 lower w/ 1" spacer, BBK 70mm throttle body & EGR, 42# inj., A/C elim., Smog Elim., Pro-M 80mm, Diablo Sport "REV Only" chip, Vortech YS trim 12#'s w/ mondo bypass, AFM Power Pipe, MSD 6AL w/ BTM, Aeromotive Competition Fuel System, Ron Davis 3 core aluminum radiator, BBK chrome shorties, MAC H-Pipe, MAC Dumps, Trans Specialties C4 w/ Trans Specialties Custom built 10 XHD HS converter, B&M Pro-Stick Shifter, UPR K-Member, w/ coil overs, Southside upper/lower control arms, Kenny Brown Sub's, Moser 33-spline's, Moser Spool, C-Clip Elim, S&W 8-point cage, 3.73's, Weld Draglites w/ 26 x 10 M/T ET Drags, and 15 x 3 1/2 Draglites on front.
Best time: 10.558 @ 130.19 w/ 1.503 60'
Posting Permissions
Reply With Quote
Bookmarks