Can't wait to get it installed. Sorry for the glare on the display.
Troy
Can't wait to get it installed. Sorry for the glare on the display.
Troy
1995 Mustang Cobra
302-10.77 @ 127.76
new motor being built
redsnk@yahoo.com
owner/moderator
http://www.stangtuning.com
Which kit is that?
Eric
1990 Mustang GT
9.20 @151.18
Check out this forum for AOD's/C4's: Click Click Racing Forums
My Homepage
They went to the wrong house. Can you pack that stuff up and ship it to me please. ;)
I love when the UPS fairy comes for a visit.:D
1998 GT
S-Trim
DSS Forged Short Block
PIs
Murillo Tuned
347hp 354ft/lb
Eric,
It's the wideband from EFI Systems, and I bought it from Total Performance (AFM also sells the wideband). I run the PMS in my car, which is made by EFI Systems, so I'm confident in this unit also. Also, love the article on the car Eric, very nice.
Troy
1995 Mustang Cobra
302-10.77 @ 127.76
new motor being built
redsnk@yahoo.com
owner/moderator
http://www.stangtuning.com
Thanks alot :) I was very happy with how it came out as well. Let me know how you like the system. I am definitely going to get something like that down the road, and I like way that particular system looks much better then the Aussie one. Are you going to use an exisiting o2 hole or weld on a new bung? My o3's are disconnected, so I was thinking of just using an exisiting hole. I do run a prochamber though which is two pieces, so it's a piece of cake to take of the drivers side pipe and take it somewhere to get a bung welded if necessary. My only concern is what will torco do to the wideband sensor since it is leaded.
Eric
1990 Mustang GT
9.20 @151.18
Check out this forum for AOD's/C4's: Click Click Racing Forums
My Homepage
Yea I will post pics and opinions once everything is installed. Brad sent me a jamb nut for the O2 sensor, which I will have my local muffler shop weld into the driver's side long tube collector. I've talked to BBBBAD5.0 on mounting the sensor etc. I do agree that this kit is better than the Tech Edge kit and much more simple to acquire. As for Torco...anything leaded will ruin an O2 sensor over time. I normally run on pump gas, but here pretty soon in preparation for FFW Houston, I am going to start using Phillips 104, which is the highest rating unleaded octane they have. Andrew on corra and few other local Texas racers have had good luck with Phillips race fuel. I'm ordering my fuel system tomorrow, so I think I will hold off and put the wideband in when I install the fuel system, or I may do it first...not sure.
Troy
1995 Mustang Cobra
302-10.77 @ 127.76
new motor being built
redsnk@yahoo.com
owner/moderator
http://www.stangtuning.com
How do you know what header to install it in? Can't one side run a good a/f and the other not?
93 LX
R331/AFR 205/Vic 5.0/? psi
Primarily I will have the sensor in the driver's side collector, based on numerous recommendations. I will weld in another bung on the passenger side, for those times when I move the sensor to the other side, but that won't happen often.
Troy
1995 Mustang Cobra
302-10.77 @ 127.76
new motor being built
redsnk@yahoo.com
owner/moderator
http://www.stangtuning.com
Troy,
Did you ever get it installed? If so, how do you like it?
Eric
1990 Mustang GT
9.20 @151.18
Check out this forum for AOD's/C4's: Click Click Racing Forums
My Homepage
Sure haven't, school has been bogging me down some. Plus I sent the meter off to get recalled, and just got it back. But the fuel system is still not here! Kinda hard to test sometthing when I can't drive the car. My fuel system needs to hurry!
Troy
1995 Mustang Cobra
302-10.77 @ 127.76
new motor being built
redsnk@yahoo.com
owner/moderator
http://www.stangtuning.com
That stinks...I know how bad it sucks sitting around waiting for parts. What fuel system are you going with?
Eric
1990 Mustang GT
9.20 @151.18
Check out this forum for AOD's/C4's: Click Click Racing Forums
My Homepage
The fuel system is way behind. He told me it was going to be shipped out Friday Feb 28th. Then a week later it never showed, called him and he said the y-blocks didn't come in. Then the next friday he said UPS forgot the shipment. That was this past friday...emailed him today and still haven't heard anything. I'm using a fuel system from Muscle Motors. Only reason I went with it was b/c it was on a GP and the deal was to good to pass up. Before this I was going to use Cartech Renegade kit, b/c I like Cartech products and they are semi-local to me. And I'm not bashing MMP or Jack, just venting some anger b/c my system is not here.
Troy
1995 Mustang Cobra
302-10.77 @ 127.76
new motor being built
redsnk@yahoo.com
owner/moderator
http://www.stangtuning.com
Bookmarks