i have a vortech s-trim. where can i get the oil line that goes from the charger to the oil pan? i bought it on ebay and it doesnt have one. and possibly the fitting too. and the line that feeds the charger oil. thanks
i have a vortech s-trim. where can i get the oil line that goes from the charger to the oil pan? i bought it on ebay and it doesnt have one. and possibly the fitting too. and the line that feeds the charger oil. thanks
You can easily make your own for the return line. I have used braided stainless and that new black nylon Aeroquip line before. No reason why you couldn't even use a piece of fuel line.
For the feed line, I normally use one of the Russel pre-fabbed -4 braided stainless lines. You can get them from the chassis shop at www.chassisshop.com.
Chris
9.05@152 with a T-Trim on BFG Drag Radials
NMCA SR6381
If you want to do something quick and cheap for now I'd suggest getting some 1/2" heater hose and look on www.mcmaster.com for the fittings you will need. I can go look up the list that I made for mine a while back. I had the same thing happen so I basically made my own lines. This winter I plan to replace them with braided SS lines
Black 2001 Mustang GT
Vortech V2-SQ aftercooled kit. Lots of custom parts made by me
I believe all you need is a 3/8 NPT to a 1/2 hose end fitting to put on the SC then 1/2 fuel line or vacuum hose. It may be 1/2 NPT..doubt it but check with vortech. Summit sells the fittings in there plumbing dept for like $5.
Like this
http://store.summitracing.com/largei...?part=MRG-2967
This would be the cheapest and fastest way.
Otherwise do SS. I did it for mine and is like $40 total.
351 "stockshort block": -Vortech T-trim (21 psi), Trick Flow Heads, Lunati Cam, Weldon fuel system, Lentech AOD., 3.55 gears, 27" Hoosier QTP's, 3500# with me
-545 rwhp
-10.02 @ 135mph---Is 9.99 to much to ask?:freaks:
-1.42-- 60'
Originally Posted by regattacoupe
so i can get 1/2" heater hose from the ace hardware i work at and a 1/2" pipe to hose fitting from there and it will work fine? whats npt mean?
Mine is a 3/8 to 3/8 fitting, from Vortech. You can use that lightweight aeroquip hose, it's just like what Vortech supplies. Lee
1988 5.0 Mustang,, 3" flair body kit, Vortech V2 S-Trim SQ, 347 FRPP Forged Stroker, Vortech V2 S-Trim SQ, FPS 200cc Alum Heads, Comp Blower Cam, G-Force T-5, Anderson Clutch,,, ect ect ect
POWDER & CERAMIC COATING - www.pristinepc.com
SUPERCHARGER BELT TENSIONERS- www.elkperformance.com
I wanna get my kicks before the whole $hithouse goes up in flames -
Yup, you can probably find the fiting at a hardware store. You have the fitting in the oil pan though...correct. If that is 1/2 you'll definitly want a 1/2 hose fitting. However if it is 3/8 then that is the fitting you'll want.Originally Posted by 90notch
NPT=National Pipe Thread. It is the style of thread pitch. The hardware will know.
Last edited by BLOWNBY; 06-22-2005 at 08:09 AM.
351 "stockshort block": -Vortech T-trim (21 psi), Trick Flow Heads, Lunati Cam, Weldon fuel system, Lentech AOD., 3.55 gears, 27" Hoosier QTP's, 3500# with me
-545 rwhp
-10.02 @ 135mph---Is 9.99 to much to ask?:freaks:
-1.42-- 60'
Originally Posted by regattacoupe
Bookmarks