Warning: preg_replace(): The /e modifier is deprecated, use preg_replace_callback instead in ..../includes/class_bbcode.php on line 2958
Dyno Numbers - Page 3
Page 3 of 6 FirstFirst 12345 ... LastLast
Results 31 to 45 of 79

Thread: Dyno Numbers

  1. #31
    SCH Moderator regattacoupe's Avatar
    Join Date
    Mar 2003
    Location
    Bucyrus oh
    Posts
    2,845
    stock 89 302-w-117,000 on the OD.
    89 Coupe with parts stacked inside of it and about 30#'s of dust on it with no end in sight. :weird:





    Although I am collecting parts for a 12.5:1 393 :D

  2. #32
    Jesus, that is truly amazing. I wonder if this humble newbie would be privileged to receive an e mail of your mods + dyno sheet. 434 RWHP is nothing short of impressive. That is right around where I want to be with a production 302 block.

    SC_graeme@shaw.ca

  3. #33
    SCH Moderator regattacoupe's Avatar
    Join Date
    Mar 2003
    Location
    Bucyrus oh
    Posts
    2,845
    It dyno'd more than i thought it would cause i dyno'd the car the same day i got my powerpipe on and it made a huge difference. Not only did it add 1.5 psi but it leaned it up a little and it was way too rich.

    email sent
    89 Coupe with parts stacked inside of it and about 30#'s of dust on it with no end in sight. :weird:





    Although I am collecting parts for a 12.5:1 393 :D

  4. #34
    Senior SCH Member
    Join Date
    Oct 2002
    Posts
    363
    i'll chime in after next tuesday. i have an appointment with Pauls Auto. in Cincinatti,OH. i'm planning on breaking the 400rwhp mark.

  5. #35
    SCH Moderator regattacoupe's Avatar
    Join Date
    Mar 2003
    Location
    Bucyrus oh
    Posts
    2,845
    good luck man. Paul's is a good shop and they'll tune it up for ya. They've done 1000's of these cars.
    89 Coupe with parts stacked inside of it and about 30#'s of dust on it with no end in sight. :weird:





    Although I am collecting parts for a 12.5:1 393 :D

  6. #36
    Senior SCH Member
    Join Date
    Oct 2002
    Posts
    363
    can he get rid of all the smog stuff? i have it all ripped off of my car but can he change it so that the computer doesn't look for any of it?

  7. #37
    SCH Moderator regattacoupe's Avatar
    Join Date
    Mar 2003
    Location
    Bucyrus oh
    Posts
    2,845
    If you had him do a chip he could. if not he can make minor adjustments and probably get you were you want to be.
    89 Coupe with parts stacked inside of it and about 30#'s of dust on it with no end in sight. :weird:





    Although I am collecting parts for a 12.5:1 393 :D

  8. #38
    Senior SCH Member
    Join Date
    Oct 2002
    Posts
    363
    i'm having him burn a chip and tune it. he said it will probably be between $500 and $700. thats around what i was planning on spending on it anyways.

  9. #39
    Senior SCH Member
    Join Date
    Dec 2003
    Posts
    127
    I was wondering. I have a single belt with a stock blower pulley and a f-150 crank pulley and am getting 10 psi, how much more boost will i get with the 2.75 inch blower pulley?

  10. #40
    Senior SCH Member
    Join Date
    Oct 2002
    Posts
    363
    i gained 3psi out of mine by having it turned down to 2.75".

  11. #41
    Senior SCH Member
    Join Date
    Dec 2003
    Posts
    127
    Hey guys i changed my combo. I took off the Holley heads off and replaced them with a set of victor jr's and replaced the xe274hr cam with a custom ground cam motion ffor the blower.

  12. #42
    Senior SCH Member lx-convertible's Avatar
    Join Date
    Oct 2002
    Location
    mass
    Posts
    473
    hey guys. saw this thread, haven't been round in a while. i made some power with mine, but never saw full potential due to burnt clutch 1st pass out. now the motor is going into my new coupe i am building as we speak.
    Neil
    Engine: DSS Pro Bullet 306, Windsor Jr. heads, E303, 42lb inj., Cobra intake(fully ported lower)65mm TB, 80mm Mass Air, MSD 6BTM, MSD coil

    Power Adder: Novi 1K, Anderson PowerPipe, ASP 8 IN Crank. No PS, AC, SMOG.

    HP: 488.3
    TQ: 461.7 Tuned by FordChip.com

    11.77 @ 119.9
    Best 60ft-1.56
    New project 1991 coupe
    NEW TOY 1995 H/D Sportster

  13. #43
    Senior SCH Member frank woodall's Avatar
    Join Date
    Jan 2003
    Location
    B'Town, Fla
    Posts
    472
    Quote Originally Posted by brad87gt
    Does anyone on here have any dyno numbers from their novi 1000 on their cars anyone with 500 plus?


    YES, I finally broke the 500 H.P. mark............. :D
    "The replacement for displacement is measured in P.S.I."
    91 Turbo GT Vert (fast)
    92 GMC Typhoon #1799
    00 Suzuki Katana
    90 LX Vert 5.0 (all stock 57,000mi)

  14. #44
    Senior SCH Member
    Join Date
    Dec 2003
    Posts
    127
    Congratulations man that is awesome. Hopefully i will be joining you in the 500 horse club as soon as this thing gets tuned. Did JMS get your chip right on the first tune?

  15. #45
    Senior SCH Member
    Join Date
    Nov 2002
    Posts
    157
    I will get mine dyno'd soon. My combo is Keith Craft 306 with ported(DaSilva performance) Edelbrock Perfomer's .500 lift cam with power pipe 42# inj with 77 mass air. No accessories on the car. Like Regatta's car.. bla bla bla. I'm running stock pulley making 7#'s boost and made 330rwhp before the blower. What is your guess having it tuned on a dyno?
    Last edited by KoolRockSteady; 03-14-2004 at 09:47 PM.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •