I recently bought a p600 and wanted to know what kind of injectors and what size you other guys are using. Also what size mass air meters are you using. I have a 75mm pro flow and 24lb injectors now and i was told that this wasnt enough. Thanks
I recently bought a p600 and wanted to know what kind of injectors and what size you other guys are using. Also what size mass air meters are you using. I have a 75mm pro flow and 24lb injectors now and i was told that this wasnt enough. Thanks
This really depends on a few factors....
How much boost you gonna run??
Do you use a FMU???
What are you goals, H/P wise and boost wise?
What's your current combo??
Dart Block 331 and No Power Adder, currently in pieces...... :weird:Originally Posted by Kato Engineering
Used to run 6.90 @ 100.4 mph in the 1/8th
My mods are cobra u&l, 75mm pro flow, 24lb injectors, cam, tremec trans, msd ignition, bbk headers to flowmasters. It is a p600b with a 2 core cooler and a 14 pound pulley. Thanks
36's may just barely work for the 14#'s, you may have to go with 42's to give you enough "play" room. Do you have any other fuel system upgrades??
Dart Block 331 and No Power Adder, currently in pieces...... :weird:Originally Posted by Kato Engineering
Used to run 6.90 @ 100.4 mph in the 1/8th
I dont have anything else. The kit came with an fmu. Should i get something else? Thanks
What size fuel pump you running??? You're gonna need a larger than stock pump (volume wise), alot of us run the Walbro 255 in tank, some of us run an additional in-line pump as well.
Dart Block 331 and No Power Adder, currently in pieces...... :weird:Originally Posted by Kato Engineering
Used to run 6.90 @ 100.4 mph in the 1/8th
I dont have a bigger pump now, but will invest in one. Also what mass air should i use?
Pro-M 80 shorty, if you plan to have your car tuned check with the place that will be doing to see which calibration they prefer/recommend. Alot of tuners prefer a non S/C'd meter vs. a S/C calibration meter for ease of tuning.
Dart Block 331 and No Power Adder, currently in pieces...... :weird:Originally Posted by Kato Engineering
Used to run 6.90 @ 100.4 mph in the 1/8th
What do you think i should do, use a walbro like you guys? Also what size maf meter are you using? Thanks again
Walbro is a solid performing quality pump and you can pick up a 255 liter per hour one for around $100.
As far as the MAf goes, I prefer the Pro-M 80 mm meter. If budget is tight I think a 75mm would serve you well.
Dart Block 331 and No Power Adder, currently in pieces...... :weird:Originally Posted by Kato Engineering
Used to run 6.90 @ 100.4 mph in the 1/8th
I already have a 75mm pro flow, will this work if it is recal'd?
If recal'd, yes.
Dart Block 331 and No Power Adder, currently in pieces...... :weird:Originally Posted by Kato Engineering
Used to run 6.90 @ 100.4 mph in the 1/8th
Do you know where and how to get it recal'd? And how much it costs. Thanks for all of your help.
$109 plus shipping according to their site
Here's the recal sheet you'd need to send with the meter.
http://www.pro-flow.com/Price%20Deal...20form%201.htm
You could sell your meter for about $100 on the Corral or here and then pick up the 80mm unit for about $200. You've have a better meter for about the same cost.
Dart Block 331 and No Power Adder, currently in pieces...... :weird:Originally Posted by Kato Engineering
Used to run 6.90 @ 100.4 mph in the 1/8th
I found a pair of 42 injectors off of a 96 gt, will these fit mine?
Bookmarks