Page 1 of 2 12 LastLast
Results 1 to 15 of 19

Thread: buying a v1 s trim

  1. #1
    Junior SCH Member
    Join Date
    Sep 2004
    Posts
    25

    buying a v1 s trim

    I need to know what kind of fuel mods i will need , i only need stuff to run a safe boost for now. The motor is stock other then mac headers. Just have a few question if you guys could help me out.

    1- what fuel mods do i need to run a safe boost

    2- what is a safe boost for this blower

    3- what size pullies will i need to run a safe boost level

    4-what kind of power gain will i get with the blow setup over the stock set up now.[ going to do a intake manifold soon]

    thanks for any help

  2. #2
    SCH Moderator regattacoupe's Avatar
    Join Date
    Mar 2003
    Location
    Bucyrus oh
    Posts
    2,845
    A 255 pump, a good quality regulator( accufab, areomotive) and in my honest opinion at least 36, but you might as well get 42's if you want to get aggresive with boost levels. With a V-1 S and a stock motor i guess it all depends on you're nerves as far as how much boost. I know i've seen alot making 14 psi on stock motors with the 2.95" blower pulley. 52,000 rpms is the max speed.
    89 Coupe with parts stacked inside of it and about 30#'s of dust on it with no end in sight. :weird:





    Although I am collecting parts for a 12.5:1 393 :D

  3. #3
    Junior SCH Member
    Join Date
    Apr 2004
    Posts
    28
    don't you think 42's might be a bit much?..i'd go with 30's and a good fmu/tune for the street. there's no reason for the big inj. if he's keeping it tame.

    i agreed with everything else...255 in-tank, ect.

    word of advice- DO NOT GET GREEDY WITH BOOST LEVELS ON A STOCK MOTOR!

  4. #4
    SCH Moderator regattacoupe's Avatar
    Join Date
    Mar 2003
    Location
    Bucyrus oh
    Posts
    2,845
    42's would be a bit much, IF he never ever wants to go any faster. How do you get a good FMU tune? I thought you have whatever you have with an FMU. Don't get me wrong i plan on running one on my 351 with 42's and the race pulley/race gas tune. With 10psi, offroad exh, and a good solid(not overly rich) tune, 330 rwhp is pretty normal with an S-trim as long as your not living in denver.

    Whats your plans GN?
    89 Coupe with parts stacked inside of it and about 30#'s of dust on it with no end in sight. :weird:





    Although I am collecting parts for a 12.5:1 393 :D

  5. #5
    Junior SCH Member
    Join Date
    Sep 2004
    Posts
    25
    plains are to just pick up some more power right now, i would say my 89 conv is a 14'sec car right now. I will run it at the track but not a lot every here and there.

    Looking to go low13's to 12's right now with out blowing it up, needsto last tell i build a new motor later, all and my motor has 120,000 miles hope this holds up to a few psi.



    thanks

  6. #6
    SCH Moderator regattacoupe's Avatar
    Join Date
    Mar 2003
    Location
    Bucyrus oh
    Posts
    2,845
    The V-1 S is usually @ 8-10 psi with a larger meter and powerpipe. I wouldn't worry about the miles as long as the car has been cared for. If you're planning on 450+ rwhp in the future it's cheaper to buy the good parts right off the bat. If not, the FMU may be the way to go for you then.........It wasn't 18 months ago i said "yes 7 psi on my novi 1000 H/C/I is all i'll ever need". Ever heard that before? :D ;) Yeah now I'm hoping for 380rwhp on the motor before i put the T-Trim on.

    It would've saved me thousands to go for the juggular right off the bat.
    Last edited by regattacoupe; 09-08-2004 at 06:46 AM.
    89 Coupe with parts stacked inside of it and about 30#'s of dust on it with no end in sight. :weird:





    Although I am collecting parts for a 12.5:1 393 :D

  7. #7
    Senior SCH Member atrimterror's Avatar
    Join Date
    Mar 2004
    Posts
    148
    If it was my car I would buy 42's and ditch the fmu. I agree with regattacoupe.
    Can't take how slow Blownby's 700rwhp car is :obscene:
    www.behindbarsracecars.com

  8. #8
    Junior SCH Member
    Join Date
    Apr 2004
    Posts
    28
    non-fmu setups are **** on the street...if you're actually going to drive it.

    big injector/no fmu setups are awesome for race applications but they load up and bog and sputter on the street.

    i don't think regattacoupe and i disagree on this...i just wouldn't run 42's on a stock motor bolt on blower car.

    i have a FULLY built short rod 347 ( that makes 425 rwhp on motor...with 8:1 comp.) with a v-1 s-trim, powerpipe ect thats makes 575 hp in street tune with 30 lbs/inj. thats hard to beat in my opinion, just based on the fact that it still gets good gas mileage...and i drive it EVERYDAY!

  9. #9
    SCH Moderator regattacoupe's Avatar
    Join Date
    Mar 2003
    Location
    Bucyrus oh
    Posts
    2,845
    My car last year with 42's idle'd like crap right off the bat....fouled plugs and the whole deal....after i got a powerpipe, play with meter clocking, timing, fuel pressure, and plug gap, and picked up a IST MAF adjuster, it idle'd like it had 24's or 30's in it. Alot of guys have picked up the Pro-m 80's and 42's and they run 100% right off the bat while others like ericbluecoupe(do a search this post may help) Tried everything I said 5 lines ago, and it still ran like crap. Turns out his MAF was cal'd slight off. He told them to take a little fuel out. He got it back and it ran like it should. MAF's are a crap shoot even though they should be plug and play. If it is rich and, or, surging, 99.99999% of all my experiance has shown the maf are the culprit. You leave no stone unturned of course but this hard for us to control without a PMS or the like.
    89 Coupe with parts stacked inside of it and about 30#'s of dust on it with no end in sight. :weird:





    Although I am collecting parts for a 12.5:1 393 :D

  10. #10
    SCH Moderator regattacoupe's Avatar
    Join Date
    Mar 2003
    Location
    Bucyrus oh
    Posts
    2,845
    bad93, I agree with you to a point. I think FMU's are pretty slick right up until 80 psi or so. They can do really wierd things for guys that try to get carried away with 19 or 24lb injector. They are great for the "blower only" car. I'm going to try one on my car that is going to make at least 600+rwhp but only because I have a wideband, 55 gallons of race fuel, and a wife thats wants a newer GT vert and a house in the country. ;)

    Sounds like you have a good grip on your tune, whats your combo?
    89 Coupe with parts stacked inside of it and about 30#'s of dust on it with no end in sight. :weird:





    Although I am collecting parts for a 12.5:1 393 :D

  11. #11
    Junior SCH Member
    Join Date
    Sep 2004
    Posts
    25
    ok guys what is the safe boost, or i guess any thing can be safe if its tuned right.

    It comes with the 8 rib Renegade stuff.........the big 8" lower and a 3" upper, how do i get my boost down to 6-8 psi or what every is safe.

    thanks for the help guys

  12. #12
    Junior SCH Member
    Join Date
    Apr 2004
    Posts
    28
    uhh...3.33" blower pulley might do it...you may need to order a 3.5'' from Ian @ SCH Racing (on the board)...i'm not real sure with the 8" crank and stock heads...i have the 8" but i'm running Edelbrock Vic Jr. 60cc heads so it's a little different.

  13. #13
    Junior SCH Member
    Join Date
    Sep 2004
    Posts
    25
    if need i can just sell the pullies on it since there new and get other ones.

  14. #14
    SCH Moderator regattacoupe's Avatar
    Join Date
    Mar 2003
    Location
    Bucyrus oh
    Posts
    2,845
    8" cranks sell like hotcakes so that won't be a problem. I reccomend stock pulleys for a stock motor for sure. I did the math for you and the blower will spin 55,000@6000rpms you don't need 18 psi do you? :D
    89 Coupe with parts stacked inside of it and about 30#'s of dust on it with no end in sight. :weird:





    Although I am collecting parts for a 12.5:1 393 :D

  15. #15
    SCH Moderator BLOWNBY's Avatar
    Join Date
    Mar 2004
    Posts
    1,380
    FWIW,

    My stock 351 short block and s-trim with 6.87/2.95 pulleys made ~530 rwhp (watch it atrimterror) at 13psi, with 42's, fmu, and base fuel pressure of 34lbs and 30* of base timing with 20* on top end. It ideled like a champ and I got 12-15 m/gallon. Barely tell it had a good size cam in it it idled so smooth. I was able to run 110 on the strip and 93 or 93 mix with 110 on the street with no problems with the BTM at 3.

    It was tuned a little conservative (Lidio Alt Auto) for the street. Ran like that for four years with NO problems.

    Point here is FMU 42's and a good tune make for very streetable set up. Now i have straight 60's and no FMU, and solid mount and still idles smooth. :D Kudos to lidio, he know how to tune a street car to run great om the street and perform well on the track.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •