6.87/3.00 uses a Mac Truck belt #88GB452P555 - 10 rib
6.87/3.00 uses a Mac Truck belt #88GB452P555 - 10 rib
89 GT TFS Heads Systemax Intake
TFS 2 cam 3:55s Novi 2000 42#ers
466hp / 409 torque ;)
10.58 @ 121 mph
I need to know what belt for a 7" and 3.25" 10 rib paxton novi 2000?
If anyone has any ideas let me know.
Jeremy
Mexican Based 331 all forged and H-Beamed
Custom Grind Supercharger Cam
AFR 205's
Holley SystemMax Stage 3 Ported Intake
Paxton Novi 2000
it should be around 56.0 inches check your local parts store i believe they should have it...the oreilys and napa here did atleast
89 GT TFS Heads Systemax Intake
TFS 2 cam 3:55s Novi 2000 42#ers
466hp / 409 torque ;)
10.58 @ 121 mph
Thanks for the reply..
You have any idea about part #.
I have a Napa here local, but there are probably going to want a part #.
Jeremy
Mexican Based 331 all forged and H-Beamed
Custom Grind Supercharger Cam
AFR 205's
Holley SystemMax Stage 3 Ported Intake
Paxton Novi 2000
not sure on the part number...just tell them you need it to be 10 ribs and 56 inches...they should be able to look it up somehow
89 GT TFS Heads Systemax Intake
TFS 2 cam 3:55s Novi 2000 42#ers
466hp / 409 torque ;)
10.58 @ 121 mph
they dont make a belt that is 10 rib and 56.0, I found a 56.7 and that was about it, I think the one they had below it was like a 54?
Anyone have any clues?
Jeremy
Mexican Based 331 all forged and H-Beamed
Custom Grind Supercharger Cam
AFR 205's
Holley SystemMax Stage 3 Ported Intake
Paxton Novi 2000
I answered you on the corral, then I came to check here. I see you beat me to it.
FoMoCo1 and I live near each other and have been searching through all these different combinations for the past month for both our motors. I didn't think they made a 56.0". You may try to go outside of the idler pulley and lengthen it to around a 57.5". Napa has a huge selection of 10 ribs from 56.5" up. They have almost every 1/2". I was going to one of their warehouse stores that I have a friend who works at and buying about 10 at a time (at ~$15-19 each). I was originally trying to do a 8" crank pulley to not void my warranty, but that didn't work. Now I have both a 3.00" and 2.75" pulley.
Anyway... you'll lose contact area, but you may find one that works if you go to the outside of the idler pulley.
1991 LX hatch AOD - Dart block, 3.25" crank, H-beams, Ross pistons, Novi 2k, TW heads, Performer RPM, 75mm TB, 80mm MAF, Bennett cam, 60lb inj., AFM Powerpipe, Kooks LTs, Snow Performance methanol/water injection, enough fuel for the Space Shuttle Discovery
Old Combo - 148k mile stock bottom end, P&P E7s, AOD, NX wet kit
428.3rwhp 566.7 rwtq
Whoever said money can't buy happiness never had a wife with breast implants. ;)
A tech at Paxton gave me the p/n for a Mack truck belt that is 55.5", 88gb449p555, might want to check it out, also the Volvo truck belt p/n for the same belt is 3895518.
Man thanks for the reply I will check it out and see if I can find one of them and give it a try.
Jeremy
Originally Posted by 93blkcoupe
Mexican Based 331 all forged and H-Beamed
Custom Grind Supercharger Cam
AFR 205's
Holley SystemMax Stage 3 Ported Intake
Paxton Novi 2000
.......Originally Posted by FoMoCo1
89 GT TFS Heads Systemax Intake
TFS 2 cam 3:55s Novi 2000 42#ers
466hp / 409 torque ;)
10.58 @ 121 mph
Hey I am gettin ready to go get one of the Mac Turck Belts, I will keep everyone informed if it is going to work with the 7"/3.25" Pulley combo.
Jeremy
Mexican Based 331 all forged and H-Beamed
Custom Grind Supercharger Cam
AFR 205's
Holley SystemMax Stage 3 Ported Intake
Paxton Novi 2000
i doubt it will fit....the 55.5 fits pretty snug on my 3.00 pulley.....although i have been wrong before
89 GT TFS Heads Systemax Intake
TFS 2 cam 3:55s Novi 2000 42#ers
466hp / 409 torque ;)
10.58 @ 121 mph
Well got some good news the 55.5" mack truck belt worked with the 7"/3.25" pulley. I did have to bump the motor over a few times to get it on, but it worked.
Jeremy
Originally Posted by FoMoCo1
Mexican Based 331 all forged and H-Beamed
Custom Grind Supercharger Cam
AFR 205's
Holley SystemMax Stage 3 Ported Intake
Paxton Novi 2000
cool...let us know how much boost the 3.25 makes
89 GT TFS Heads Systemax Intake
TFS 2 cam 3:55s Novi 2000 42#ers
466hp / 409 torque ;)
10.58 @ 121 mph
I managed to squeeze a k080545 onto my Renegade setup with a 7 / 3.0 :)
Last edited by Chad89GT; 01-07-2005 at 08:59 PM.
Bookmarks