Can some of you guys post what boost you're seeing and what size pulley you're running. I'm just looking for a general range....I'm running the stock 10-rib (Is that a 4" pulley???) that came with my 2000 and seeing 8 lbs....
Thanks.
Can some of you guys post what boost you're seeing and what size pulley you're running. I'm just looking for a general range....I'm running the stock 10-rib (Is that a 4" pulley???) that came with my 2000 and seeing 8 lbs....
Thanks.
1991 Teal GT / NOVI 2000
so far....12.26 @114 @ 8lbs on a stock AOD w/ shift kit (stock heads / GT-40 intake / stock converter)
OThe stock pulley size is 3.50 and is rated at 8-10 pounds of boost. It will vary depending on your combo. On a stock motor you will see 10 pounds. If you add heads, intake, cam, you will probably see 8 pounds. One problem with the 10 rib kit is that the belt was a little too long and it would allow slippage above 5800. Check your tensioner to make sure that is not bottomed out. If it is I can give you a part number for a gates belt that will work. Another suggestion would be to add a power pipe. With it you will see an increase of 2-3 pounds. Hope this helps
Doug
14-1 compression 402ci with a little nitrous
I have an anderson pipe, and I'm only seeing 8-lbs....I'll check the belt tension tonight, but I swear it's larger than 3.5".....It measures 4" outer diameter...... maybe I'm imagining things...
I have a GT-40 intake / 65mm TB, and 73mm C&L with 30lb injectors... but that's it so far for the motor....hopefully I'll have a set of heads on it soon....
1991 Teal GT / NOVI 2000
so far....12.26 @114 @ 8lbs on a stock AOD w/ shift kit (stock heads / GT-40 intake / stock converter)
chris messure the top of the groves on the pully !! also get a 80mm mass air i was pulling 10 to 11 on that gauge when i had it!! let me know or stop down and ill install my meter to show you !!!chad
im trying to put a 3.15 pulley on my charger but my stock belt is to long, will this gates belt work on my novi2000...OThe stock pulley size is 3.50 and is rated at 8-10 pounds of boost. It will vary depending on your combo. On a stock motor you will see 10 pounds. If you add heads, intake, cam, you will probably see 8 pounds. One problem with the 10 rib kit is that the belt was a little too long and it would allow slippage above 5800. Check your tensioner to make sure that is not bottomed out. If it is I can give you a part number for a gates belt that will work. Another suggestion would be to add a power pipe. With it you will see an increase of 2-3 pounds. Hope this helps
novi2000,gt40heads(iron),gt40 intake,4.10gears,1.7rockers.etc best et 11.84 @ 118.5 60ft:1.74
if yes, could i have the part number
The belt that Paxton sent with my kit translates to Gates #K100570. The belt number I used was Gates #K100563. This is the part number I used. It only cost about $26.00 dollars at Carquest auto parts, but it them 2 days to order it.
Doug
14-1 compression 402ci with a little nitrous
You're 73mm Mass Air meter is probably the culprit here. When I ordered my Novi 2000, Jack from Muscle Motors informed me to run an 80mm Mass Air on a Novi 2000. He said a 73mm will cost you at least 2 lbs of boost because it's too restrictive for the large inlet of the Novi.Originally posted by CopMagnet
I have an anderson pipe, and I'm only seeing 8-lbs....I'll check the belt tension tonight, but I swear it's larger than 3.5".....It measures 4" outer diameter...... maybe I'm imagining things...
I have a GT-40 intake / 65mm TB, and 73mm C&L with 30lb injectors... but that's it so far for the motor....hopefully I'll have a set of heads on it soon....
yes it will hawk jake is correct!!
OK well looks like I'm going to have to save up.....Chad did you have one on the car before then?
1991 Teal GT / NOVI 2000
so far....12.26 @114 @ 8lbs on a stock AOD w/ shift kit (stock heads / GT-40 intake / stock converter)
i have a 92mm mass air that im triying to put on my anderson power pipe, but cant find a rubber hose to fit the mass air and the power pipe. the ones from home depot are to small or way to big anyone know where i could get rubber hose to fit perfect. pro-m 92mm mass air and anderson power pipe.thanks
Keep an eye on eBay for one. I got my C&L 80mm brand new with the electronics (the actual meter) and 3 sampling tubes for $120 US. I also believe Ian (88 Cobra) is selling his Pro-M for a good price in the buy & sell section. I'm not sure how big it is though.Originally posted by CopMagnet
OK well looks like I'm going to have to save up.....Chad did you have one on the car before then?
FWIW, I was seeing 11-12#s @ 6200 with stock pullies and no power pipe and a 80mm C&L.
yes chris i did havea 80mm pro m on there and i didnt have a power pipe on it either!! chad
We are seeing 30psi @7200 rpm with a 8" crank and a 3.25 blower pulley.
Bookmarks